Product ID:RAMSET EPCON SYSTEM-RESIN PART A
MSDS Date:10/02/1987
FSC:8010
NIIN:00N042081
Kit Part:Y
MSDS Number: BSTBK

ITW PHILADELPHIA RESINS CORP

130 COMMERCE DR
MONTGOMERYVILLE, PA 18936
US

Emergency Phone: 215-855-8450

Info Phone: 215-855-8450

Cage: ITWPH

ITW PHILADELPHIA RESINS

454 MONTGOMERYVILLE, PA 18936 US

Telephone: 508-777-1100

Cage: ITWPH

DO NOT INDUCE

RTECS: 9999999ZZ

IN

RTECS: 9999999ZZ

DIGLYCIDYL ETHER OF BISPHENOL A; (EPOXY RESIN). LD50

AMORPHOUS SILICON DIOXIDE; (AMORPHOUS SILICA, SILICON

CAS: 68855-54-9

ACGIH TLV: SEE INGREDIENT NAME

TALC (POWDER), CONTAINING NO ASBESTOS FIBERS; (TALC,

CAS: 14807-96-6

RTECS: WW2710000

OSHA PEL 2 MG/M3 RDUST

ACGIH TLV: 2 MG/M3 RDUST

TITANIUM OXIDE; (TITANIUM DIOXIDE)

CAS: 13463-67-7

RTECS: XR2275000

OSHA PEL 10 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST

GLASS OXIDE

CAS: 65997-17-3

ACGIH TLV: 15 MG/M3 TDUST (MFR)

LD50 LC50 Mixture:SEE INGREDIENT 1.
Routes of Entry: Inhalation:NO Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:SKIN:RESIN IS MOD IRRIT & MAY CAUSE
SENSIT. EYE:MOD IRRIT. CORNEAL DMG IS UNLIKELY. INHAL:BECAUSE OF
ITS VERY LOW VOLAT, PROD IS NOT LIKELY TO PRDCE ANY ADVERSE EFTS BY
INHAL.HAZS ASSOC W/FILLERS, ING S 2-5,SHOULD NOT APPLY UNLESS CURED
MATL IS GROUND/MACHINED SO AS TO PRDCE DUST. INGEST:RESIN IS GEN
CONSIDERED (SUPDAT)
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:IRRITATION AS NOTED. SKIN SENSITIZATION
(ALLERGY) MAY BE EVIDENCED AS RASHES, ESPECIALLY HIVES.
Medical Cond Aggravated by Exposure:PRE-EXISTING SKIN ALLERGIES MAY
INCREASE CHANCE OF DEVELOPING INCREASED ALLERGY SYMPTOMS FROM
EXPOSURE TO PRODUCT. PRE-EXISTING SKIN AND EYE DISORDERS MAY BE
AGGRAVATED BY EXPOSURE TO THIS PRODUCT.

First Aid:EYE: IMMED FLUSH W/PLENTY OF WATER FOR AT LST 15 MINS WHILE
HOLDING EYELIDS OPEN. GET MED ATTN. SKIN: IMMED REMOVE CONTAMD
CLTHG. WIPE EXCESS FROM SKIN & FLUSH W/PLENTY OF WATER FOR AT LST
15 MINS. US E SOAP IF AVAIL/FOLLOW BY WASHING W/SOAP & WATER. DO
NOT REUSE CLTHG UNTIL THORO CLEANED. GET MED ATTN. CONTAMD LEATHER
ARTICLES, INCL SHOES, CANNOT BE DECONTAM & SHOULD BE DESTROYED.
INHAL: (SUPDAT)

Flash Point:>250F,>121C
Extinguishing Media:FOAM, CARBON DIOXIDE, DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NONE KNOWN.

Spill Release Procedures:AVOID PERSONAL CONTACT. TAKE UP WITH ABSORBENT
MATERIAL. PLACE IN A SUITABLE CONTAINER FOR WASTE DISPOSAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:STORE IN COOL DRY PLACE WITH ADEQUATE
VENTILATION; KEEP AWAY FROM OPEN FLAME AND HIGH TEMPERATURES.
Other Precautions:PRACTICE GOOD HOUSEKEEPING PROCEDURES TO AVOID ALL
SKIN CONTACT AND BREATHING OF VAPORS. HANDLE IN ACCORDANCE WITH
HAZARD POTENTIAL OF CURING AGENT. WASH THOROUGHLY AFTER HANDLING,
AND BEFORE SMOKING, EATING OR USING TOILET FACILITIES.

Respiratory Protection:NOT ORDINARILY REQUIRED FOR RESIN. RESPIRATORY
PROTECTION SHOULD BE SUITABLE FOR ALL WORKING CONDITIONS ON JOB.
NIOSH/MSHA APPROVED DUST MASKS SHOULD BE WORN DURING ANY GRINDING
OR MACHINING PROCEDURE S ON CURED RESINS.
Ventilation:GEN: GOOD GEN VENT IS USUALLY ADEQ FOR MOST INDUS APPLIC.
LOC EXHST: SHOULD BE USED IN CONFINED AREAS/WHERE VAP (SUPDAT)
Protective Gloves:IMPERVIOUS RUBBER OR PLASTIC GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:WEAR CLEAN LONG LEG AND SLEEVED CLOTHING.
Work Hygienic Practices:PRACT GOOD HOUSEKEEPING PROCS TO AVOID ALL SKIN
CONT & BRTHG OF VAPS. WASH THORO AFTER HNDLG, & BEFORE SMOKING,
(SUPDAT)
Supplemental Safety and Health
MATLS TO AVOID: REACTED W/UNCONTROLLED AMTS OF CURING AGENT. HAZ DECOMP
PRODS: ALDEHYDES,& ACIDS (TOX/CORR). HLTH HAZ: TO HAVE LOW ORDER OF
ACUTE ORAL TOX. VENT: CONC EXCEEDS ESTABLISHED TLV'S. HYGIEN E
PRACT: EATING/USING TOILET FACILITIES. FIRST AID PROC: REMOVE
VICTIM TO FRESH AIR & PROVIDE OXYGEN IF BRTHG IS (ING 6)

HCC:N1
Spec Gravity:1.5 (H*2O=1)
Solubility in Water:NEGLIGIBLE
Appearance and Odor:WHITE PASTE WITH MILD EPOXY ODOR.

Stability Indicator/Materials to Avoid:YES
CAN REACT VIGOROUSLY W/STRONG OXIDIZING AGENTS & STRONG LEWIS/MINERAL
ACIDS. CONSIDERABLE HEAT CAN BE RELS WHEN (SUPDAT)
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:AS W/ANY ORG MATL,COMBUST WILL PRDCE
CARBON DIOXIDE (SIMPLE ASPHYX).OTHER DECOMP PRODS MAY INCL CARBON
MONOXIDE,(SUPDAT)

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH FEDERAL, STATE AND
LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.